Under the Network section, select Firewall, and then Port Forwards.10.10.10.0/24) in the вЂњRestrict Masquerading to given source subnetsвЂќ option Enter the local network and mask (e.g.Under the Network section, select Firewall, and then General Settings.For example, a machine allocated a Local IP of 10.10.10.137 will map to 1.2.3.137.For ease-of-administration, set the last octet of the local address to the same as what the static IP will be.Create a static lease for each system that will use a static IP.Under the Network section, select LAN Settings.Continue adding additional вЂњIP-AliasesвЂќ entries for the remaining Usable Addresses.In the вЂњAdvanced SettingsвЂќ tab, in the вЂњIPv4-BroadcastвЂќ, enter the вЂњBroadcast AddressвЂќ (e.g.For the вЂњIPv4-GatewayвЂќ, enter the Router Address (e.g.For the вЂњIPv4-NetmaskвЂќ, enter the Subnet Mask (e.g.For вЂњIPv4-AddressвЂќ, enter the first вЂњUsable AddressвЂќ (e.g.

After reloading, find the вЂњSTATIC1вЂќ section.

Under the вЂњIP-AliasesвЂќ section, enter вЂњSTATIC1вЂќ and click вЂњAddвЂќ.

In вЂњGeneral SetupвЂќ tab, ensure the вЂњProtocolвЂќ setting is вЂњDHCP ClientвЂќ.

Under the Network section, select Interfaces, for the вЂњWANвЂќ network, click the вЂњEditвЂќ button.

Ensure that the router is working normally (Dynamic WAN IP), and the modem has been configured, before following these steps.

Under the Firewall section, ensure the following settings:.

Ensure that вЂњCascaded Router EnableвЂќ is set to вЂњOffвЂќ.Set the вЂњPrimary DHCP PoolвЂќ to вЂњPrivateвЂќ (WeвЂ™ll let the router assign these later).Set the вЂњAllow Inbound TrafficвЂќ option to вЂњOnвЂќ.In the DHCPv4 End Address, enter the highest вЂњUsable AddressвЂќ (e.g.In the DHCPv4 Start Address, enter the lowest вЂњUsable AddressвЂќ (e.g.In the вЂњPublic Subnet MaskвЂќ, enter the Subnet Mask (e.g.In the вЂњPublic IPv4 AddressвЂќ, enter the Router Address (e.g.Set the вЂњPublic Subnet EnableвЂќ option to вЂњOnвЂќ.Leave the Private LAN Subnet section as-is.Under the Home Network section, click Subnets & DHCP.Under the Home Network section, click Wireless.Connect to the management website by navigating to.Ensure that the modem is working normally before following these steps.This tutorial will walk you through the steps necessary to get an Almond+ Router (firmware R076 OpenWRT-based) working, while also keeping the вЂњDynamic IPвЂќ that will still be associated with the U-Verse modem, allowing 6 total IPs to be used.ДЇor the sake of this tutorial, weвЂ™ll assume the following configuration information is provided by AT&T: When configuring AT&T U-Verse with Static IPs, youвЂ™ll be assigned a block of 8 IP addresses, 5 of which are вЂњusableвЂќ. Aside from the router, no other devices will be connected to the AT&T modemвЂ™s built-in switch or WiFi. Configuring AT&T U-Verse NVG589 for Static IPs with Pass-Through to Almond+ OpenWRT RouterДЇor this tutorial, we will be configuring the network so that all client systems and IP addresses will be managed via the Almond+ router.

At&t router configuration